Drinking Water Sampling Instructions

Sampling, Storage & Transportation of Drinking Water Samples.
Drinking Water Sampling Instructions

Different bottles for different tests...

INTRODUCTION

The objective of sampling is to obtain a representative volume of the water to be consumed as drinking water and to store and transport that sample in such a manner as to limit any changes that may occur in the sample before it is analysed.

SAMPLING POINTS

Samples can be taken from a variety of sampling points, including drinking tap, well, spring, storage tank, borehole or surface water. In domestic premises samples should be taken at a tap used to supply water for drinking or cooking purposes. In food production premises samples should be taken at a point immediately before the point where the supply is used for food production and after any treatment given to the water before use.

SAMPLING OF POTABLE WATER
1. PRINCIPLE

Samples are taken in such a manner that they are:

    • representative of the water received by the consumer
    • not contaminated by any material which could affect any future chemical or bacteriological test
2. HEALTH & SAFETY

All relevant health and safety codes should be observed at all times when undertaking sampling activities.

3. PROCEDURE

Taps should be in good repair. If they leak between the spindle and the gland when the tap is turned on, ideally, they should not be used. Samples required from a particular sample point must be taken in a specific order.

a.   Chemical Sampling

    1. If a sample requiring testing for a metal or metals is requested this must be taken before flushing the tap and before taking any other sample. Fill the bottle with the first draw from the tap. Do not rinse the bottle.

    2. Flush the tap for at least two minutes.

    3. Take all other chemical samples required.

b.   Sterilisation of Taps

    1. Remove any attachments, filters and/or devices from the tap, clean the inner and outer surfaces of the tap spout with a clean tissue moistened with chlorine solution or alternatively, a disinfectant wipe. This procedure should be repeated until the surfaces of the taps are clean.

    2. Turn on the tap and run the water to waste at a uniform rate for at least one minute to ensure that the chlorine/disinfectant solution is rinsed away before taking the bacteriological sample.

c.   Bacteriological Sampling

This is taken following chemical sampling. Bacteriological examination is an extremely sensitive technique and can easily be ruined by contamination. Please observe the following:

      • Never hold the bottle by the neck.

      • Never flush out the bacteriological bottle prior to taking the sample. Ensure that a pre-sterilised bottle is used as indicated by the tape on the bottle being intact. Ensure that the bottle is within its expiry date. If the sterile tape indicator or the expiry date is not satisfactory DO NOT USE the bottle.

      • Never lay the bottle down on the ground, on a fence post or on any other area that animals may have been in contact with as this may cause cross contamination of bacteriological samples.

        1. Reduce the flow if necessary to achieve an even flow before sampling.

        2. Remove the top from the bacteriological bottle.

        3. Do not lay the top down. Hold the top firmly between the fingers of one hand with the open end down. Do not allow the fingers to touch the inner surface of the top and do not turn the top over.

        4. Without changing the water pressure place the bottle in the stream of water from the tap and fill to the base of the neck leaving a small gap at the top to allow mixing in the laboratory. Do not allow the bottle to overflow. (If the bottle does overflow or the top of lip of the bottle touches either your hand or the tap, discard this bottle and take a new bottle.)

        5. Carefully replace the top.

        6. Turn off the tap.

        7. Label all the bottles, at the time of sampling, with their appropriate pre-printed labels or hand written label with (as a minimum) site, purpose, time and date of sampling.

        8. Store the bacteriological bottle upright in a cool place, protected from light and deliver to the laboratory as soon as possible.

CONTACTING US

If you have any questions about this document, please contact us by visiting our Contact page.

Add comment

You can add a comment by filling out the form below. Plain text formatting.

Products
More…
Services
More…
Company
More…
Related Items
Thinking of renovating your property? Thinking of renovating your property?

Sand, cement, lime and other building materials have only recently been well defined, renovations ...

Bacteriological Sampling Bacteriological Sampling

Sampling, Storage & Transportation of Water Samples for Bacteriological Testing.

The Chemistry of Life The Chemistry of Life

The Periodic Table currently has 118 well defined and well characterised chemical elements, but ...

The Dawn of Life The Dawn of Life

The chemistry of every living thing is defined by six elements, from these six elements four ...

It's A Bugs Life... It's A Bugs Life...

Do they know how hard we work for them, do they even know what we do?